Camshafts & Valvetrains

Trick Flow® hydraulic lifters and lash adjusters are the perfect choice to freshen up your engine during a cam swap. These affordable lifters and adjusters are designed to factory tolerances for a perfect fit and provide precise oil control to keep...

This high-grade steel distributor gear from MSD is specifically designed for use with the EFI 5.0L and 351W engines utilizing a hydraulic roller camshaft.  The gear is made for a distributor shaft diameter of .531".  

Generation 3 model You've asked, we've listened. Anderson Fabricated Aluminum Mustang Valve Covers with fill tube and 10AN fittings for remote catch can setups. No longer do you need to cut and make your own breather holes for a catch can on your...

Generation 3 model You've asked, we've listened. Anderson Fabricated Aluminum Mustang Valve Covers with fill tube and 10AN fittings for remote catch can setups. No longer do you need to cut and make your own breather holes for a catch can on your...

Anderson screw-on breather for stock Mustang 5.0 valve covers (No Logo) Fits: 1979 Mustang,1980 Mustang, 1981 Mustang, 1982 Mustang, 1983 Mustang, 1984 Mustang, 1985 Mustang, 1986 Mustang, 1987 Mustang, 1988 Mustang, 1989 Mustang, 1990 Mustang, 1991...

Anderson Cam Chain Retention ToolWith all of the cam testing we have done over the years on the 4.6 two valves, Anderson Ford Motorsport has developed a time-saving tool.This tool is used to remove the camshafts in the 4.6 two valve engines that are...

Anderson F-42 Two valve Camshaft for PI Heads & OEM stock pistons RPM range 2400-6200 Forced Induction  8-13 lb. 4.6 Best performer up to 6200 rpm. Nice idle, good driveability down to 1800 rpm,performance range 2400-6200 rpm. Recommend AFM...

Anderson F-52 Two valve Camshaft for PI Heads with AFM Valve Springs & Aftermarket pistons/ valve reliefsRPM range 2500-6200Forced Induction 8-13 lb. 4.6 Best performer up to 6200 rpm. Nice idle, good driveability down to 1900 rpm, performance...

Anderson F-82 Two valve Camshafts for PI Heads with AFM Valve Springs & aftermarket pistons/valve reliefsRPM range 2800-7200 Forced Induction 13lb. plus 4.6 Best performer up to 7200 rpm shift point. Rough idle, good driveability down to 2400 rpm,...

1.47" diameter, 1.800" install height, Inside diameter .700"Seat pressure 150lb @ 1.800", open pressure 450lb @ 1.200"   MAX LIFT .600"Springs are dual with damper Spring retainers are 10-degree, steel Valve locks are 10-degree, steel, for...

1.51" Diameter, 1.850" Recommended Install HeightSeat Pressure 200lb @ 1.850", Open Pressure 460lb @ 1.250"   MAX LIFT .600", Coil Bind 1.18" Recommended for boosted applications at or above 17 psi with our Anderson Hi-Rev series...

Anderson Hi-Rev Valve Springs for 2V P.I. heads. Must have for Anderson Hi-Rev camshaft. Replace part 221427 Maximum Valve Lift (in.): 0.580 in. Outside Diameter of Outer Spring (in.): 1.125 in. Coil Bind Height (in.): 1.080 in. Spring...

Anderson Steel Lined Rubber Valve Cover Gaskets. Fits all 86-95 5.0L/5.8L SBF engines. Perfect for use with AF-6582 series valve covers! Rubber gasket with steel core creates perfect seal and are reusable. Sold as a pair

Anderson Steel Retainers.  Fits HR-22018 Valve Springs, 10-Degree.

Anderson Steel retainers for HR-15018 and HR-20018 valve springs, 10 degree.

Anderson 10 degree steel, 11/32" locks

B-21 Camshaft works with stock OEM pistons with 1.7 roller rockers.  RPM range 2400-6200. Hydraulic Roller. Steel Core. Use steel camshaft gear.Same as B-31 except utilizing 1.7 R.R. N2O or S/C 8-15 lb 302 c.i.d. Best performer for 1.7 R.R., stock...

B-31 Camshaft works with stock OEM pistons with 1.6 roller rockers.  RPM range 2400-6200. Hydraulic Roller. Steel Core. Use steel camshaft gear.N2O or S/C 8-15 lb 302 c.i.d. Best performer for 1.6 R.R., stock pistons and 6200 rpm. Great with TFS or...

B-31HR Camshaft works with stock OEM pistons with 1.6 roller rockers. Must check piston to valve clearance. RPM range 2500-6500. Hydraulic Roller. Steel Core. Use steel camshaft gear. This is the cam used in AFM's project "Everyman"S/C 10-20lb 302-331 c...

B-41 Camshaft.  Requires aftermarket pistons and 1.6 roller rockers.  RPM range 2700-6500. Hydraulic Roller. Steel Core. Use steel camshaft gear.N2O or S/C 10-20 lb 302-347 c.i.d. Best performer for 6400 rpm. Great with TFS or Edelbrock heads...